Fire Retardant MSDS for Leather Seal 3 for Tanneries by Flame Seal Products Inc.

LEATHER SEAL™ 3

Public Stock : F L M P MSDS (Material Safety Data Sheet)

EMERGENCY TELEPHONE NO.: 800-424-9300

PRODUCT NAME: Leather Seal™ 3 Fire Retardant (No PBDEs - Polybrominated diphenyl ethers)

CHEMICAL FAMILY: Aqueous based fire retardant penetrant/coating.

SECTION I - PRODUCT INFORMATION

MANUFACTURER’S NAME: FlAME SEAL PRODUCTS, INC.

4025 WILLOWBEND BLVD. #310

HOUSTON, TX 77025 USA

(713) 668 4291

Exclusive Industrial Sales Agent:

Atlas Refinery: 973 589 2002 office, 973 589 7377 fax., www.atlasrefinery.com

SECTION II - HAZARDOUS COMPONENTS

COMPONENT		ACGIH	OSHA
CAS REGISTRY NO.	WT. %	TLV	PRL
Sodium Bromide 7647-15-6	5% - !0%
Potassium Bromide 7758-02-3	1% - 5%
Boric Acid 10043-35-3	0.5% - 1.5
Phosphoric Acid 7664-38-2	<.1%	500 ppm TWA 500 ppm STEL	400 ppm TWA 500 ppm STEL

SECTION III - PHYSICAL PROPERTIES

APPEARANCE AND ODOR: Semi-clear, odorless liquid.

MOLECULAR WEIGHT: Not Applicable.

BOILING POINT: (DEGREES FAHRENHEIT): 212 - N/A

MELTING POINT: (DEGREES FAHRENHEIT): Not Applicable.

VAPOR PRESSURE: (mm of Mercury): Not Determined.

SPECIFIC GRAVITY: (WATER=1): 1.14– 1.18

VAPOR DENSITY: (AIR=1): Aqueous mixture not determined.

PERCENT VOLATILE: (BY WEIGHT): 80% - 85% (water content only)

pH: 2.0 - 3.0

SOLUBILITY IN WATER: Complete.

EVAPORATION RATE: (BUTYL ACETATE=1): Not Determined <1 (slower).

SECTION IV - FIRE AND EXPLOSION DATA

FLASH POINT (DEGREES FAHRENHEIT: PENSKY-MARTENS CLOSED CUP): None to boiling.

FIRE EXTINGUISHING MEDIA: Not combustible. Use water spray, fog, foam, dry chemicals, CO₂, or other agents as appropriate for material in surrounding fire.

FLAMMABLE LIMITS (PERCENT BY VOLUME): Not applicable.

SPECIAL FIRE FIGHTING PROCEDURES AND EQUIPMENT: Not combustible.

UNUSUAL FIRE AND EXPLOSION HAZARDS: None

HAZARDOUS COMBUSTION PRODUCTS: Exposure to high heat and / or combustion may cause liberation of traces of ammonia.

SECTION V - REACTIVITY DATA

STABILITY: STABLE ___X___ UNSTABLE _______

CONDITIONS TO AVOID: Mixing & strong bases/ Mixing with incompatible materials.

INCOMPATIBILITY (MATERIALS TO AVOID): Strong bases may emit ammonia gas.

HAZARDOUS DECOMPOSITION PRODUCTS: In the dry state, nitrogen oxides, ammonia or hydrogen bromide may be formed in the presence of fire.

HAZARDOUS POLYMERIZATION: Will Occur _______ Will Not Occur ___X___

SECTION VI - HEALTH HAZARD INFORMATION

EXPOSURE FROM ROUTINE USE: No evidence of adverse effects from available information.

EFFECTS OF OVEREXPOSURE: EYES. . . Direct contact with eyes may cause irritation.

PROBABLE ROUTES OF EXPOSURE: Eyes, inhalation, and ingestion.

EMERGENCY AND FIRST AID PROCEDURES:

EYE CONTACT: Immediately flush eyes with water for at least 15 min. including underneath eyelids. Consult a physician if irritation persists.

SKIN CONTACT: Non-irritant; wash from skin.

INHALATION: Not established. Not expected to be harmful.

CARCINOGENICITY: Not applicable.

OTHER PERTINENT DATA: Not applicable.

SECTION VII - TOXICITY DATA

ORAL: Acute Oral Toxicity: Ld50 (rat) > 5000 mg/kg

DERMAL: Not established, not expected to be harmful. May be irritating with continual contact.

INHALATION: Not established. Not expected to be harmful. If necessary, use respirator if adequate ventilation is not available to keep exposure to particulate matter (dry) or mist (wet) at a minimum.

OTHER PERTINENT DATA: Not applicable.

SECTION VIII - SPECIAL PROTECTION INFORMATION

PERSONAL PROTECTION EQUIPMENT

PROTECTIVE GLOVES: Ordinary protective work gloves.

EYE PROTECTION: Safety goggles.

RESPIRATORY PROTECTION (SPECIFY TYPE): Use NIOSH approved equipment suitable for nuisance vapors when airborne exposure is necessary.

OTHER PROTECTIVE EQUIPMENT: Wear easily washable clothing.

SECTION IX - SPILL, LEAK, AND DISPOSAL PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Confine spilled material and absorb on sand, sawdust, earth or other available solids. Sweep and place in a suitable container. Flush with water and rinse minor spills into sewer if permitted by Federal, State and local regulations.

WASTE DISPOSAL METHODS: Incinerate or bury in a suitable land fill where permitted by appropriate government regulations.

CLEAN WATER ACT REQUIREMENTS: Not applicable.

RESOURCE CONSERVATION AND RECOVERY ACT (RCRA) REQUIREMENTS: No applicable information found.

SECTION X - REGULATORY INFORMATION

FDA: No applicable information found.

USDA: No applicable information found.

CPSC: No applicable information found.

TSCA: No applicable information found.

DOT: No applicable information found.

PROPER SHIPPING NAME: Not applicable.

HAZARDOUS CLASS: Not applicable.

LABEL REQUIRED: Not applicable.

IDENTIFICATION NUMBER: Not applicable.

This information is furnished without warranty, representation, inducement or license of any kind, except that it is accurate to the best of Flame Seal Products, Inc. knowledge, or obtained from sources believed by Flame Seal Products, Inc. to be accurate, and Flame Seal Products, Inc. does not assume any legal responsibility for use or reliance upon same. Customers are encouraged to conduct their own tests. Before using any product, read its label.

EFFECTIVE DATE: February 4, 2005
SUPERSEDES: April 7, 2004

Exclusive Industrial Sales Agent:

Atlas Refinery: 973 589 2002 office, 973 589 7377 fax., www.atlasrefinery.com , info@atlasrefinery.com

® Registered in US Patent and Trademark Office ™ Trademark of FLAME SEAL PRODUCTS INC.

(Non Toxic, Non Hazardous, No PBDEs - Polybrominated diphenyl ethers)

Manufacturer Address: FLAME SEAL PRODUCTS, INC. 4025 Willowbend Blvd. # 310, Houston, Texas, 77025 USA, (713) 668 4291 office, (713) 668 1724 fax, Website: www.flameseal.com Email: flameseal@flameseal.com